供应200W伺服驱动器MCAC506

MCAC506 all-digital AC servo drive system adopts high-performance digital signal processor (DSP) and integrated circuit, and come out to be a cost effective product with simple circuit, high integration, easy operation, and strong practicability. MCAC506 provide three feedback loops: position loop, velocity loop and current loop. Three work control mode: position, velocity and torque. MCAC506 matches with AC servo motor under 50V and 200W.

 

Position control: light isolate input PULSE/DIRECTION or CW/CCW signal

Speed control: input simulate 0-3.3V voltage signal (speed input by Pos.ff)

Torque control: input simulate 0-3.3V voltage signal (torque input by Pos.ff)

Light isolation servo reset input interface ERC

Light isolation servo failure alarm output interface ALM

Width of current loop (-3dB) 2KHz (standard)

Width of velocity loop: 500 Hz (standard)

Width of position loop: 200 Hz (standard)

Quadrature encoder input interface at motor side: differential input (26LS32)

Allow parameters download by pc or text displayer through interface RS232C

Perfect protection against overload, I2T, over-voltage, over current, overheating, short circuit, circuit interruption, chip damage

Green light for on, red light for protected mode or offline.

 

Input DC voltage range 20—50v(standard)

Continuous Output power:200W

Continuous output current:6A 32KHz PWM

Overload output current: 18A(3s)

Protection:

Over current initiated peak value: 30A±10%

Overload I2T current initiated value: 300% 5s

Overheating initiated value: 80℃

Over voltage initiated value: 65 v

Under Voltage initiated value: 18V

 

Maximum pulse input frequency:300K

Maximum RS232C speed: 19.6Kbps (an extra transfer interface required)

Working environment:

No dust, no oil mist and no corrosive air

Working temperature: 0-50℃

Storage temperature: -20+80℃

Humidity:40-90RH

Cooling method: natural air cooling and forced air cooling

 

Dimension: 118 x 76 x 35 mm

Weight: about 200g

 

 

(potentiometer adjusting, CCW to minimize value, CW to maximize value)

 

A) Four pins on the Circuit Board for control mode setting, 1, 2, 3, 4 respectively from the outer side.

1.      no plug in, position mode is pulse/direction

2.      plug in 1, speed control, speed input by Pos.ff

3.      plug in 2, torque control, torque input by Pos.ff

4.      plug in 1 and 2, position control for positive pulse/negative pulse input

5.      plug in 3, position control pulse/direction, but converse running direction.

 

B) 11 scale on the potentiometer, CCW to minimize the value to 0, CW to maximize the value to 10, and 5 in the middle.

Pos.ff : Position Feed-forward Control

Pos.P: position proportional gain control

Pos.D: position differential control

Vel.p : velocity proportional gain control

Tor. P: Current proportional gain control

 

Servo system includes three feedback loop: position, velocity and torque(current). The inner loop responses with the fastest speed, and the middle loop must responses faster than the outer loop. A vibration will happen when the rule has not been followed. Customer need adjust the parameter of position loop and velocity loop only. Parameters of system would restrict each other, the output of position feedback would be unstable when just only the position feedback gains, which would lead to an unstable result of the whole servo system. Customer might take the following adjustment procedure as a reference:

1.      set Pos.ff and Pos.D to (3) on the potentiometer, set the Pos.P and Vel.p to (3), and then increase the Vel.p slowly till a vibration happens, then return 0.5 to 1 scale.

2.      increase the Pos.P till a vibration happens, and then increase the Pos.D till the vibration disappears.

3.      increase the Pos.ff to fulfill a minimum lag and overshoot.

4.      decrease the Vel.p properly when a vibration happens during the motor operation.

5.      decrease the Pos.P or increase the Pos.D properly when a vibration happens when the motor stop.

6.      decrease the current properly when a magnet noise happens.

 

Maximize the Pos.P under the condition of none overshoot and no vibration. And then minitrim the Vel.P, Pos.ff and Pos.D till a perfect setting.

 

X1: control signal input / output

 

X2: feedback signal input of encoder(D15 female)

 

X11:control signal input / output(four pins)

 

X3: power

 

 

 

Single terminal connection                       Differential connection